Showing 129–144 of 293 results
Helmet Mounted Ear Muffs
High Expansion Foam Generator
High Foam SX 2%
High Velocity Water Spray Nozzles
Horizontal Split Case Pump
- Standardized design with reliable performance
- The cast iron casing is axially split which permits removal of the complete rotor without moving either piping or motor. Pumps generating high heads have double volutes to reduce radial forces, ensuring minimal shaft deflection and low bearing loads.
- The bronze closed type impellers have double curved vanes. The double suction design gives practically zero axial forces. Each impeller is statically and dynamically balanced.
- The carbon steel shaft is fully sealed against the liquid being pumped. Shaft protecting sleeves are fitted in the seal area.
- Replaceable cast iron rings protect the casing at the impeller running clearances.
- Stuffing box is fitted with mechanical seal. Pump can be supplied with gland packing also.
- Bearings are grease lubricated deep groove ball type.
Standard Material
| Casing | Cast Iron |
|---|---|
| Shaft | Carbon Steel |
| Impeller | Bronze |
| Wear Ring | Cast Iron |
Hydraulic Concentrate Ball Valve
Hydraulic Tools
iEvac Smoke/Fire Hood
Impulse Valve System
In-line Foam Inductor
Industrial Firefighting Vehicles
- For protection of industrial assets NAFFCO provides a complete range of vehicles able to carry large amounts of foam, dry powder and water. The chassis are provided with safety futures as spark arresters and engine shut off valves, in line with the internal regulations of the industrial sector.
- Chassis commonly used are Mercedes, MAN, Iveco ,International or Freightliner.
- Cabin can be single or double cabin subject to chassis selection.
- Tanks options of Glass Reinforced Polyester (GRP), Polypropylene or SS 316L.
- Equipments are available upon request.
- Foam systems are highly accurate balanced pressure or electronic injection type.
- Monitors with electric or manual control dual or triple agent can be provided.
- High pressure hose reel with electric rewind available on selected models.
- Water towers with heights up to 50 meters can be installed on selected models.
| Model | Drive | Minimum HP | Cabin | Water Tank (L) | Foam Tank (L) | Fire Pump Capacity (LPM@10 bar) | GVW (T) | More Info. |
|---|---|---|---|---|---|---|---|---|
| NFI-30/30-DC | 6×4 | 310 | Double | 3,000 | 3,000 | 4,000 | 27 | |
| NFI-50/50-DC | 6×4 | 310 | Double | 5,000 | 5,000 | 6,000 | 31 | |
| NFI-60/60-SC | 6×4 | 390 | Single | 6,000 | 6,000 | 6,000 | 33 | |
| NFI-0/11-DC | 6×4 | 390 | Double | NA | 11,000 | 10,000 | 33 | |
| NFI-0/22-SC | 6×4 | 480 | Single | NA | 22,000 | NA | 35 |
Industrial Packaged Fire Pump Sets
NAFFCO package fire pump system consists of pumps, driver, controllers and accessories mounted on a common base frame. High quality UL / FM certified components are used in these systems complying with the requirements of NFPA 20. All necessary wiring between controllers and drivers are done at factory prior to shipment. The automatic air release valve, casing relief valve, suction gauge & discharge gauge are mounted on fire pumps and other accessories are mounted on pre-constructed interconnecting piping as required by NFPA 20. Pressure sensing lines are pre-installed on Electric, Diesel, and Jockey Controllers as per NFPA 20 requirements.
These systems are subjected to rigorous performance tests at factory as per UL, FM & NFPA standards to ensure proper performance of the system as per the design requirements. For completing the installation of these pre-engineered ‘ready to install’ packages the installing contractor only needs to grout the structural base, connect the suction & discharge pipes and incoming power.